Load AutoCAD Create the roof plan below using rectangle and line command. Write a QBasic program to enter names, Date of Birth, Place of Birth, State of Origin, Sex, Age You are to print out the hard copy of your source code.

The outer rectangle has a width of $12 \text{ mm}$ and a height of $5 \text{ mm}$. Let's assume the bottom-left corner of the rectangle is at coordinates $(0,0)$.
The central horizontal line segment of the roof plan is formed by the intersection of the diagonal lines. Due to the symmetry of the diagram, this central line will be at half the height of the rectangle, so $y = \frac{5}{2} = 2.5 \text{ mm}$.
Let the left endpoint of this central line be $P_L = (x_L, y_L)$ and the right endpoint be $P_R = (x_R, y_L)$.
The diagonal line from the bottom-left corner $(0,0)$ to $P_L$ makes an angle of $60^\circ$ with the bottom edge (x-axis).
The slope of this line is $\tan(60^\circ) = \sqrt{3}$.
The equation of this line is $y = \sqrt{3}x$.
Since $P_L$ lies on this line and $y_L = 2.5 \text{ mm}$:

Numerically, $x_L \approx 1.443 \text{ mm}$.
So, the left internal point is $P_L = \left(\frac{5\sqrt{3}}{6}, 2.5\right)$.
By symmetry, the right internal point $P_R$ will have an x-coordinate $x_R = 12 - x_L$:

Numerically, $x_R \approx 10.557 \text{ mm}$.
So, the right internal point is $P_R = \left(\frac{72 - 5\sqrt{3}}{6}, 2.5\right)$.

Use the RECTANG command to draw the main outline.
RECTANG
Specify first corner point: 0,0
Specify other corner point: 12,5

Use the LINE command to draw the four diagonal lines and the central horizontal line.

• Draw the bottom-left diagonal: LINE Specify first point: 0,0 Specify next point: 1.443,2.5
• Draw the bottom-right diagonal: LINE Specify first point: 12,0 Specify next point: 10.557,2.5
• Draw the top-left diagonal: LINE Specify first point: 0,5 Specify next point: 1.443,2.5
• Draw the top-right diagonal: LINE Specify first point: 12,5 Specify next point: 10.557,2.5
• Draw the central horizontal line: LINE Specify first point: 1.443,2.5 Specify next point: 10.557,2.5

Part 2: QBasic Program

a) Write a QBasic program to enter names, Date of Birth, Place of Birth, State of Origin, Sex, Age.

CLS ' Clears the screen

' Declare variables
DIM Name AS STRING
DIM DateOfBirth AS STRING
DIM PlaceOfBirth AS STRING
DIM StateOfOrigin AS STRING
DIM Sex AS STRING
DIM Age AS INTEGER

' Input data from the user
INPUT "Enter Name: ", Name
INPUT "Enter Date of Birth (DD/MM/YYYY): ", DateOfBirth
INPUT "Enter Place of Birth: ", PlaceOfBirth
INPUT "Enter State of Origin: ", StateOfOrigin
INPUT "Enter Sex (M/F): ", Sex
INPUT "Enter Age: ", Age

' Display the entered information (optional, but good practice)
PRINT
PRINT "--- Entered Information ---"
PRINT "Name: "; Name
PRINT "Date of Birth: "; DateOfBirth
PRINT "Place of Birth: "; PlaceOfBirth
PRINT "State of Origin: "; StateOfOrigin
PRINT "Sex: "; Sex
PRINT "Age: "; Age

END ' Ends the program

b) You are to print out the hard copy of your source code.
This means you should print the QBasic program code (the text shown above) onto paper. In QBasic, you would typically save the program file and then use a print command from the QBasic editor or operating system to get a physical copy.